Saillogger Community

Hi - I used the iframe suggested to embed the real time tracking on a webpage (www.brazenarticle.com) which is a work in progress. I noticed in the iframe code "scrolling - no". Does that mean behaviors of the monitor can be changed?

I'd like the default display to be the map, not the satellite view. Would it also be possible to change the color of the track from gray to red, blue or anything brighter?

I realize this may be getting in the weeds quite a bit and sincerely appreciate the ability to share the real time monitor with family and friends.

The same applies to additional batteries when I want to see voltage and state of charge. Is it possible to duplicate the provided battery display which shows voltage and SOC in one small package?

Thanks, I found a problem with one of the gps sources. Turned it off and Saillogger shows correct heading.
I'm underway now and boat speed is showing up, I'll check the log tonight. Attached is a screenshot from yesterday's log showing zero. It has been showing correctly while moving but zero on the processed log for the last several days.

Hello - My real time monitoring page shows the boat icon facing almost 180 degrees off the boat heading. It also correctly shows the boat speed while underway.
The finished log for each segment corrects the boat icon but shows boat speed as zero.

That was simple! I didn't realize that empty space was part of the list.
Thanks...

Hello - I tried this new feature and I am able to change the Tracking Page Start to different trips but so far I cannot clear the field to turn this feature off. I'm on a MacBook Air using Safari.

Thanks - I configured the GPS source and will keep an eye on it when I'm on the move again. I'll also read through the FAQs again, lots of good information in there!

Speed over ground is on the N2K network, it appears multiple times in data browser, pointing to different N2K PGNs. I'm not sure how to edit or eliminate a source, perhaps another option is to map one of the sources as a priority?
I appreciate you taking the time to help me figure this out.

One of the logs is #14804 From Coconut Grove Sailing Club to Tarpon Basin North (referenced in note above).
When I click on the log view it shows zero boat speed at some points, incorrect speed at others. Wind speed seems okay.
Log #15157 is a short trip from fuel dock to mooring, it shows wind speed but no boat speed.

When on the move with realtime monitoring the boat speed has been zero. Not sure when that started, my recollection is it worked fine some weeks ago.

Stupid question here....how do I download a specific trip as a csv so I can see all the data points? I'm pretty sure I've done that in the past but now I'm just downloading the log summary page

SignalK windspeed seems correct, it is apparent wind, not true wind.
environment.wind.speedApparent

In the realtime monitoring and in recorded logs I am seeing zero boat speed most of the time. Sometimes the boat speed will show up but it is incorrect, almost like it is adding wind speed and boat speed.
The log from February 1, 2024 shows this....
Any ideas or suggestions to get it back to normal?

Brazen Article
Time 2/1/2024, 12:02:16 PM
Boat Speed 0 knots
Wind Speed 5.7 knots
Latitude 25.388367
Longitude -80.2637928

Brazen Article
Time 2/1/2024, 12:07:19 PM
Boat Speed 11.1 knots
Wind Speed 6 knots
Latitude 25.3823747
Longitude -80.2693225

Would it be possible to display the track in realtime monitoring? Maybe the previous hour, or ideally the position back to midnight or whenever the boat started moving for the day.

Wow - that is dedication! Thanks, the inside information that was blank is no longer displayed

Thanks for the quick response! I don't have inside temperature or humidity, no "inside" paths at all in data browser. In the plug in when I delete the two inside values they immediately pop back in place when I hit submit or leave the plug page.
Not sure if that is what you mean by block level or if something else is going on.

Right now the Timelapse simply runs from end to end, with the possibility of pausing.
A slider bar to move forward or back on the track is of great benefit. I use this feature in another program (Floathub) to look at tracks into an anchorage from previous trips, sometimes from prior years.

Thanks for the new monitoring page, it looks great - a big improvement and hopefully it will continue to develop.
I don't use "Inside Temperature" or "Inside Humidity" and found when I left them blank they didn't appear on the monitoring page. Some time later the tabs were back. In SignalK I deleted the path but as soon as I hit submit it filled in again. I can't leave it blank now.
Is there some way of keeping the unused elements off the monitoring page?